Emulsion YC 4101

For use with UV, solvent based and water based inks.

Suncoat YC4101 is a dual sensitized emulsion capable of producing photo-stencils of an extremely high quality.

It should be used where high deinition and resolution are required and is recommended for 4 colors process printing.

YC 4101 is a two pack system and is available in pack size 0.9 kilos.

Dual cure diazo emulsion 1068

For Textile printing with inks containing water and solvents. Ideal for plastisols !

glass and ceramic printing.

1. Description

−  Fast dual cure polymer screen emulsion; purple. 

−  Sensitizing with separate diazo powder: C2 for 1 kg set, C7 for 4,5 kg 

set. 

−  The ready to print screens can be post-exposed to increase the printing 

resistance. 

−  For longer runs a chemical hardening (catalyzing) is necessary. 

2. Application advantages

−  Solids content after sensitizing: 41%. 

−  High viscosity. 

−  Good transparency. 

−  Excellent water- and solvent resistance. 

−  Extra good flexibility. 

3. Coating technique and stencil

• Fast dual cure polymer screen emulsion; Purple

• Sensitizing with separate diazo powder: C2 for 1 kg set, C7 for 4,5 kg set

• Solids content after sensitizing: 41%

• High viscosity

• Good transparency

• Excellent water- and solvent resistance

• Extra good flexibility

1 kilo

SOLO Screen Emulsion one component ready-to-use.

Presensitized screen emulsion; red :

• High viscosity for coarse and fine meshes
• Excellent flow-out; avoiding pin-holes caused by too fast coating
• Usable on white and yellow mesh
• Fast wash-out
• Excellent resistance to solvent based inks and its screen washes
• Decoatable with all chemicals used for emulsion stencil removal

1 kilo

FOTECOAT 1846 SOLO

Ready-to-coat, one component Presensitized photopolymer screen emulsion for thick stencils.

• Solvent resistant
• Blue
• No mixing, no degassing
• 44% of solids

Characteristics :

• Ready-to-coat, one component screen emulsion.
• Thick stencils are achieved by coating wet in wet up to 20 strokes from the squeegee side.
• Fast exposure time.
• Patience needed for stencil wash-out.

Fotechem 2154 is a liquid solution that significantly increases the life of under-exposed emulsions by completing the exposure process.

It is used immediately after frame development and can be used with all emulsions in the FOTECO range.

After development, simply apply the concentrated product with a sponge to both sides of the screen, leave for one minute, then rinse. 

Strengthen under-exposed emulsions! and simplify reclaiming

Water resistant screen filler Fotechem 2077 WR

This is a water resistant screen filler with self-drying characteristics and low viscosity.

It can be used in combination with water based inks or adhesives and low resistant screen emulsions. To improve the water resistance, Fotechem 2077 WR can be hardened chemically (Fotechem 2100 or 2130 or 2110 ; For application, see Technical Information in the link below).

Before decoating the stencil, the Fotechem 2077 WR screen filler must be removed.

Available in 1 liter pot

Suncoat Fast Blue Filler

This filler has been designed for blocking out open areas of mesh and retouching pinholes in finished stencils. The formulation of allows it to dry quickly at room temperature.

This will reduce processing time and increased the speed of the screen to press.

This product is resistant to conventional UV, Plastisol and solvent based inks only.

Application Tips :

This is a fast drying screen filler for blocking out open mesh between the stencil edge and the printing frame.

• Put the filler onto the open areas in small quantities and spread across the mesh with a piece of card plastic
• Turn the screen over and repeat
• Very coarse meshes may need a further application

Available in 1 liter pot

Speedball Screen Drawing fluid

This liquid will help you to carry out, in all simplicity, your screen of screen printing.

Application tips :

1. Place your screen in a horizontal elevated position
2. Paint fluid over areas to print
3. Allow to dry
4. Apply screen filler on same side used with Drawing fluid
5. Apply with squeegee one even pass coat and allow to dry
6. Wash drawing fluid out with cold wate.
7. Scrub area that remain blocked lightly with a small stiff brush
8. Allow screen to dry horizontally

The Drawing fluid must be used with Speedball screen filler.

236.5 ml

HPR Light bulb

Do your exposition yourself with a low cost system.

• Light bulb for silkscreen
• Capacity of 125 wats
• Need a specific transformer and a socket

Transformer for the HPR bulb

Many tansformer and bulb can be connected to expose large size screen.